login

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Qynx

Pages: [1] 2
1
Here you can find a usable library for the HX711

https://www.dfrobot.com/wiki/index.php/Weight_Sensor_Module_SKU:SEN0160

best regards,

Rob
2
Project Questions / Guidelines / Re: Reading microSD cards on Wiring
« on: June 26, 2016, 04:33:28 AM »
I had no  experience reading microSD cards on Wiring...



A good reason to start with it.......  Any questions ?








http://www.soran.edu.iq
3
In hardware/Atmel, edit the boards.txt file,
4
Wiring Hardware Questions / Re: Unable to load sketch to Wiring V1.0
« on: August 09, 2015, 07:23:26 PM »
Jim,

Give  me your adress in a PM.


I can sent you a board you can use: for free (wiring service)


5
Yes, it was browser related.....
After this weekend I start with it.
6
uh.. maybe it's my browser, but I don't see included files???  :-[
7
Please share the library, i'm very busy but I can try.

Regards,


Rob
8
OK, succes......

I use this also with ATMEGA128 (pin compatibel)

Regards,

Rob
9
If you have a PCB with the mega128 you can use this with Wiring, but not with the  644 bootloader.

I use wiring with my ecb1 PCB with Mega128, but with a Mega128 bootloader.

You get a 644  massage because you select the wrong board.

This is my used Mega128 board:

http://lynxshop.nl/ivendi/index.php?dispatch=categories.view&category_id=271

Best regards,

Rob
10
I think its not. the FTDI driver.....  You forgot to remove  a sign by installing Java, this is the only install I know wich installing this toolbar.....


Rob
11
LiquidCrystal myDisplay = LiquidCrystal(0,1,2,2);

must be:

LiquidCrystal myDisplay(2, 3, 4, 5, 6, 7); // RS E DB4 DB5 DB6 DB7




Syntax   
display.print(data)
display.print(data, base)

must be:

myDisplay.print(data)
myDisplay.print(data, base)

http://www.wiring.org.co/reference/libraries/LiquidCrystal/LiquidCrystal_print_.html



12
Project Questions / Guidelines / Re: Resistor Question
« on: November 11, 2013, 12:51:45 AM »
I'ts beter to use a regulator, I think.

But it depends on the motor current.
And the 9v battery's are normal Max 150ma also not the best choice.

Please give more information.


13
Installation Questions / Re: Close comport after uploading
« on: August 20, 2013, 07:17:58 PM »
Brevig,

The last Message is:

Uploading.....


And it looks he's ready with uploading,  I try to make a small movie tomorrow  so its more clear wat the problem is.

Rob
14
Installation Questions / Re: Close comport after uploading
« on: August 19, 2013, 05:49:05 PM »
Hi Brevig,

I use a V1.0 compatible board  atmega 128 and FT232RL
I use this  board with Mega128  and Mega1281 or mega2561

Works great, but not on my new windows 8 desktop.

http://easycircuitboard.nl/

Best regards,

Rob
15
Installation Questions / Close comport after uploading
« on: August 18, 2013, 07:45:45 AM »
I have a problem on my current desktop PC with windows 8.

If I use the USB on the front Windows is not see the FTDI chip.
But if I use the USB on the back side windows is installing the drivers and
everything seems ok....

But,  after uploading a sketch the COM Port is not closed.

After a timout from AVRdude the port is not closing. and Wiring keeps displaying

Uploading...

So I have to disconnect the board so windows is closing the Comport and Wiring say there is a serial error.

After that and reconnecting I can open the terminal window and by closing the terminal the
COMport is closed.

It looks a problem between AVRdude and wiring.

I'm using Windows 8 on a 64 bit system


Pages: [1] 2