login

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - ldalep

Pages: [1]
1
Programming Questions / Re: Pullup no works
« on: November 15, 2011, 08:26:51 AM »
 :)

Thanks that worked only  off by 10.

const int FADEAMOUNT = 10;
const int PUSHBUTTON = 12;
const int RESET = 17;   // A3;
const int GREENLED = 9;
const int REDLED =14; // A0;
const int YELLOWLED = 10;
const int REL1 = 15; // A1;
2
Programming Questions / Re: Pullup no works
« on: November 14, 2011, 12:52:01 PM »
Any word on this issue.... do you need more info
3
Thank You

I can do.... I suspect they will reject the file I gave them...
4
 :)
Thanks for the quick response......

So I have gotten in touch with the vendor - They would prefer to work with a "hex" file.  Is this a correct idea or assumption:

If I created a .elf file which contains all of the info that is needed - FUSE, FLASH, EPROM, LOCK, then used avr-objcopy with out any exclusions that the hex file that is generated is one that they can use?  I looked at the one I had generated and it had all of the info based upon the ihex intel format?

5
 :-\

What is the process using wireing or anything else but avr studio to get the complete .ihex file for a vender/supplier burn.  Seems like the ones I have been looking at don't give everything at once.  For example if you do a bootload reburn you get the fuse settings, but if you do just a flash through the bootloader you don't get all the fuses... just new and not knowing.
6
Programming Questions / Re: Pullup no works
« on: November 10, 2011, 12:18:36 PM »
Thanks for the quick responce

I have a key pad and some buttons in the sketch that worked fine in ardrunio land.  I used the writedigital to use the internal pull up resistors.  Now some of the pins (A3) for one and some of the keypad pins no longer work   

I am using the Adrurino Pro (5V 16Mhz) w/atml328

As an aside I can get the keyboard to work fine in wiring when I use just the Keyboard example sketch

Code: [Select]
#include <Keypad.h>
#include <EEPROM.h>
//#include <MsTimer2.h>
#include <TimedAction.h>



const byte ROWS = 4; //four rows
const byte COLS = 3; //three columns

String Inputstring="";
String Cmdstring="";
boolean Master = false;
boolean Sechalf= false;
unsigned long inval=0;
int Rtime=0;

int rel1count=0;
int TOGGLEcount=0;

int Codelen=0;
int keycounter =0;
boolean keyboardlk=false;

boolean pb=false;
boolean rel1=false;
boolean TOGGLE=false;
boolean valpart=false;
int memslot=0;

const int FADEAMOUNT=10;
const int PUSHBUTTON=12;
const int RESET =A3;
const int GREENLED =9;
const int REDLED = A0;
const int YELLOWLED =10;
const int REL1=A1;

const int STARTMEMREL1 = 0;
const int ENDMEMREL1 = 297;
const int MEMTOGGLE = 300;
const int R1ENTRY=20;
const int CODLEN=4;

const int MEMREL1TIME= 305;
const int MEMREL2TIME= 307;
const int MEMBOOT=511;
const int DEFR1SEC=5;


const int MEMMASTER = 310;
const unsigned long DEFMASTER=1234;
const unsigned long MAXINT=1048575;

char keys[ROWS][COLS] = {
  {
    '1','2','3'                  }
  ,
  {
    '4','5','6'                  }
  ,
  {
    '7','8','9'                  }
  ,
  {
    '*','0','#'                  }
};
byte rowPins[ROWS] = {
  2, 4, 5, 7}; //connect to the row pinouts of the keypad
byte colPins[COLS] = {
  8, 6 , 3}; //connect to the column pinouts of the keypad
int brightness = 125;    // how bright the LED is
int fadeAmount = 0;    // how many points to fade the LED by
//int incomingByte = 0; // for incoming serial data

Keypad keypad = Keypad( makeKeymap(keys), rowPins, colPins, ROWS, COLS );
TimedAction timedout = TimedAction(60000,abort);
TimedAction clocktime = TimedAction(500,Timeclear);

void setup(){
  Serial.begin(9600);

  Codelen=CODLEN;
  //MsTimer2::set(60000, abort); // 500ms period
  //MsTimer2::stop();
  timedout.disable();
  clocktime.disable();
  pinMode(GREENLED, OUTPUT);
  pinMode(REDLED,OUTPUT);
  pinMode(YELLOWLED,OUTPUT);
  pinMode(REL1,OUTPUT);



  pinMode(RESET,INPUT);
  digitalWrite(RESET,HIGH);
  //pullup(RESET);

  pinMode(PUSHBUTTON,INPUT);
  digitalWrite(PUSHBUTTON,HIGH);
  //pullup(PUSHBUTTON);

7
Programming Questions / Pullup no works
« on: November 09, 2011, 09:44:31 PM »
 ???
I have an ardruno sketch that when I compiled it in wiring I noticed that the pullups no longer worked.  I have tried in vain going from

digitalwrite(XXX, HIGH)
to
pullup(XXX)

no worky ATML328P 16mhz
Pages: [1]