login

Recent Posts

Pages: [1] 2 3 ... 10
2
Wiring Implementations / Need advise
« Last post by Hedda on February 19, 2019, 02:18:12 AM »
We built a house and the builder wired the house for alarm with the help of his friend. So the doors and windows have got sensors that are wired into the house. We haven't activated the system with alarm monitoring services, but now want to do that. I am trying to find out what can be done with the pre-wired system.
I looked online at reviews.  I want something that uses cellular instead of a landline, which is good because I don't have a landline in my house. And I'd like the one that I can control through my smartphone/tablet etc. Future expansion/integration into home automation is a plus. Cost is not a factor. I'm willing to pay top dollar if it will do what I want.
Any insights?
3
Programming Questions / Re: Programming with ISP
« Last post by alanjones on January 25, 2019, 05:30:42 AM »
If you need anykind of source code programming then visit https://epsonsupports.net/blog/fix-reset-ink-cartridge-epson/ to know about it in details.
4
Wiring Hardware Questions / Re: Adding variable switch/dial to air hockey table fan.
« Last post by Lucilla on September 14, 2018, 09:25:18 AM »
Hello there, https://athletesphysiques.com/trenbolone-review-results/ some info on Trenbolone I would really recommend the big switch small switches are not that good had the same problem once, I switched to big and it is solved now
5
Programming Questions / Re: Has anyone programmed a MPS20n0040D-S Pressure Sensor?
« Last post by Qynx on July 21, 2018, 01:15:42 AM »
Here you can find a usable library for the HX711

https://www.dfrobot.com/wiki/index.php/Weight_Sensor_Module_SKU:SEN0160

best regards,

Rob
6
Programming Questions / Has anyone programmed a MPS20n0040D-S Pressure Sensor?
« Last post by m6powers on June 06, 2018, 01:05:17 PM »
I am running an Arduino UNO with a SparkFun HX-711 Load Cell AMP. I am trying to find a good program to use
to get my sensor to read pressure and to check out out my connections. I had to Solder the HX-71 and need to make sure it is working. With this being my first go at programming, I am running blinded my my inexperience.
                      Thanks for any help!
7
I have a couple of 120v AC fans that came from old air hockey tables, they currently have a toggle switch to turn them on and off however I would like to be able to control there speed instead of it just being full on or off as they are quite noisy at max. I have limited knowledge with electronics and I don't typically mess with mains voltage but I was curious if this was possible and if so what type of switch I could use or what would be best. I would prefer a small switch similar to the one it already has but I would also be fine using a bigger one if needed.

Any suggestions are greatly appreciated.

8
Wiring Hardware Questions / Reviving the original Wiring (ATmega128a) board?
« Last post by westfw on March 15, 2018, 06:34:32 AM »
(How depressing; most of the Forum Messages in the last several years are spam.)

Anyway, the ATmega128a is fantasticly cheap these days (from China), and I had some interest in creating an old-style Wiring board aimed at hand assembly...
And it's pretty much working...
https://hackaday.io/project/62511-revive-wiring
9
Installation Questions / Re: Installing Wiring in Linux
« Last post by Sibiler on December 21, 2017, 11:47:00 AM »
i'm sorry for replying to an old thread but I am having problems installing wiring on Linux and I was wondering if someone can help me, thanks, wanna do it now that i sit home doing nothng but searching for meds reviews. any help would be appreciated!
10
General Developer Discussion / How to get the hex?
« Last post by GilMata on December 07, 2017, 01:00:39 PM »
Hello I wrote code in wiring but my question is how to get the .hex in arduino ID this is generated in temp but i don't know where is it in wiring.

or this is not possible to get
Pages: [1] 2 3 ... 10